#Irlp tyt uv8000e how to
#Irlp tyt uv8000e serial number
#Irlp tyt uv8000e upgrade
#Irlp tyt uv8000e plus

(I personally own an older version 3 of the TYT TH-UV8000D radio that doesn't support the cross-band function, and I have no plans to sell it, as I also own a more expensive Wouxun KG-UV8D Plus hand-held that also supports the cross-band repeat function. Yes, the TYT factory 'could', but the cost to you would easily exceed the cost of a new radio.

#Irlp tyt uv8000e upgrade

Before you ask, TYT dealer's can't upgrade the firmware in older models. You need to have the latest radio firmware in the TYT radio for this cross-band feature to work, and most of the radio's available on the internet are sold by folks that don't test their radios prior to shipment and haven't a clue of how they really work.

Remember, not all TYT TH-UV8000D radios have the cross-band repeat function supported in the radio's firmware. Simply go back to Menu 11 and change the option back to вЂњOFFвЂќ. Be sure to remember to turn off the cross-band function before changing your frequencies or when done with your cross-band repeater use. Any signal heard on your VHF frequency will be repeated by the radio to your UHF frequency (and vice-a-versa). Your cross-band repeat function is now active. Push the 'U/V' button to exit the Menu selection choice and your display will once again show your two chosen frequencies (or memories). Push the 'F' (function button) again to activate Menu 11 and change the option shown to 'ON' Push the 'F' (function button) and either enter 11 on your keypad or turn your channel knob to Menu 11 Set your bottom VFO B with your UHF frequency of choice (between 400-520 MHz) Set your top VFO A with your VHF frequency of choice (between 136-174 MHz) The cross-band repeat function also supports CTCSS (or PL) tone encoding if you choose to use it. channel or memory mode) in the new V4 TH-UV8000D radio, but both modes will work with the cross-band repeat function (when properly set up).

#Irlp tyt uv8000e how to

Not only will that help preserve battery life, but your radio will be much cooler and the battery will last longer as well.ДЇifth, the example that follows will show you how to set up a cross-band repeat function in VFO mode (vs. Since one advantage of the TH-UV8000D radio is that it comes with a higher performance (and longer) gain antenna, try using the low power setting when using the cross-band repeat function whenever possible. their mobile radio counterparts that have both a larger heat sink and a fan for cooling), so it's highly recommended that you keep your cross-band transmissions as short in duration as possible and NOT use high power unless absolutely necessary. Instantly re-transmitted on your selected UHFДЇourth, hand-held radios do not have cooling fans (just a relatively small heat sink vs. Heard on your selected VHF frequency will be V4 of the TYT TH-UV8000D radio will operate inД«oth directions automatically, meaning that a signal Third, the cross-band repeat function in the new Separation to accomplish the same task (plus itД¬osts a lot less and removes many pounds of Radio designers use many MHz of frequency Hand-held radio like the TYT TH-UV8000D, so the Picture on right) that's just not feasible in a small KHz apart on VHF (using expensive receiverД¬avities to separate the two close-by signals, see Have transmit and receive frequencies just 600 Repeater costing several thousand dollars can Several MHz of separation between the transmitДЄnd receive frequencies in order to performД¬orrectly, so while an expensive commercial

#Irlp tyt uv8000e serial number

To ensure that each unit has been tested prior to shipment, we record each radio's serial number after testing and before shipment to the customer.Д¬ommunications, a cross-band repeater needs First, not all TYT TH-UV8000D radios have the cross-band repeat function supported in the radio's firmware (all current versions shipped by RF Gear 2 Go have been tested by us prior to shipment to ensure that you get the latest radio firmware, thus allowing the cross-band repeater function to work).